Zone 5 Basement Wall Insulation — R-10
The DOE recommends R-10 insulation for the basement wall in Climate Zone 5 (Cool). The typical basement wall cavity depth is 4 inches. This page compares all insulation types showing the thickness needed, material cost per square foot, and whether each type fits within the standard cavity depth.
Quick Summary
Insulation Type Comparison for Zone 5 Basement Wall
The following table compares all insulation types for achieving R-10 in the basement wall of a building in Climate Zone 5. Types marked as "recommended" are specifically suited for this building component. The cost estimates represent material costs only and do not include labor, which can add 30-100% depending on the insulation type and project complexity.
| Insulation Type | R/Inch | Thickness | Cost/SqFt | Cost/1000 SqFt | Fits Cavity | Recommended |
|---|---|---|---|---|---|---|
| Extruded Polystyrene (XPS) | R-5 | 2" | $1.80 | $1,800 | Yes | Yes |
| Mineral Wool Board | R-4.3 | 2.3" | $2.50 | $2,500 | Yes | Yes |
| Closed-Cell Spray Foam | R-6.5 | 1.5" | $8.00 | $8,000 | Yes | Yes |
| Blown-In Cellulose | R-3.5 | 2.9" | $0.70 | $700 | Yes | - |
| Blown-In Fiberglass | R-2.5 | 4" | $0.80 | $800 | Yes | - |
| Vermiculite (Loose Fill) | R-2.1 | 4.8" | $1.00 | $1,000 | No | - |
| Fiberglass Batt | R-3.2 | 3.1" | $1.20 | $1,200 | Yes | - |
| Expanded Polystyrene (EPS) | R-3.9 | 2.6" | $1.20 | $1,200 | Yes | - |
| Mineral Wool Batt | R-3.3 | 3" | $1.50 | $1,500 | Yes | - |
| Cotton Denim (Recycled) | R-3.5 | 2.9" | $2.00 | $2,000 | Yes | - |
| Polyisocyanurate (Polyiso) | R-6 | 1.7" | $2.20 | $2,200 | Yes | - |
| Sheep Wool | R-3.5 | 2.9" | $3.50 | $3,500 | Yes | - |
| Open-Cell Spray Foam | R-3.7 | 2.7" | $4.00 | $4,000 | Yes | - |
| Aerogel Blanket | R-10 | 1" | $30.00 | $30,000 | Yes | - |
Installation Guidance
Basement wall insulation at R-10 in Zone 5 can be installed on either the interior or exterior of the foundation wall. Interior insulation is more common in existing homes and typically involves attaching 1 to 2 inches of rigid foam (XPS or polyiso) directly to the concrete wall using adhesive, followed by a framed wall with optional additional cavity insulation and drywall. This approach provides a continuous vapor and thermal barrier against the concrete while creating a finished interior surface. Never install fiberglass batts directly against concrete basement walls, as moisture will condense on the cold concrete surface, saturate the fiberglass, and promote mold growth. Closed-cell spray foam is an excellent alternative that provides insulation, air sealing, and vapor protection in a single application. Exterior basement insulation using rigid XPS is applied during construction and extends from the top of the foundation to at least 2 feet below grade, protected by a durable coating above grade.
Construction Notes
Basement wall insulation can be installed on the interior or exterior of the foundation wall. Interior insulation is most common in existing homes and typically involves attaching rigid foam insulation directly to the concrete wall, followed by a framed wall with additional cavity insulation and drywall. Exterior insulation is applied to the outside of the foundation during construction and must extend from the top of the foundation to at least 2 feet below grade. Closed-cell spray foam and rigid XPS are preferred materials for basement walls because they resist moisture and do not support mold growth. Never install fiberglass batts against concrete basement walls without a moisture barrier, as condensation will saturate the fiberglass and promote mold.